Common Emitter (CE) Configuration

Common Emitter (CE) Configuration

The name itself implies that the Emitter terminal is taken as common terminal for both input and output of the transistor. The common emitter connection for both NPN and PNP transistors is as shown in the following figure.

Just as in CB configuration, the emitter junction is forward biased and the collector junction is reverse biased. The flow of electrons is controlled in the same manner. The input current is the base current I_B and the output current is the collector current I_C here.

Base Current Amplification factor (β)

The ratio of change in collector current (ΔIC$\mathrm{\Delta }{I}_C$) to the change in base current (ΔIB$\mathrm{\Delta }{I}_B$) is known as Base Current Amplification Factor. It is denoted by β

β=ΔICΔIB$$\beta =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_B}$$

Relation between β and α

Let us try to derive the relation between base current amplification factor and emitter current amplification factor.

β=ΔICΔIB$$\beta =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_B}$$

α=ΔICΔIE$$\alpha =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}$$

IE=IB+IC$$I_E=I_B+I_C$$

ΔIE=ΔIB+ΔIC$$\mathrm{\Delta }{I}_E=\mathrm{\Delta }{I}_B+\mathrm{\Delta }{I}_C$$

ΔIB=ΔIE−ΔIC$$\mathrm{\Delta }{I}_B=\mathrm{\Delta }{I}_E-\mathrm{\Delta }{I}_C$$

We can write

β=ΔICΔIE−ΔIC$$\beta =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E-\mathrm{\Delta }{I}_C}$$

Dividing by $$

β=ΔICΔIEΔIEΔIE−ΔICΔIE$$\beta =\frac{\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}}{\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_E}-\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}}$$

α=ΔICΔIE$$\alpha =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}$$

We have

α=ΔICΔIE$$\alpha =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}$$

Therefore,

β=α1−α$$\beta =\frac{\alpha }{1-\alpha }$$

From the above equation, it is evident that, as α approaches 1, β reaches infinity.

Hence, the current gain in Common Emitter connection is very high. This is the reason this circuit connection is mostly used in all transistor applications.

Expression for Collector Current

In the Common Emitter configuration, I_B is the input current and I_C is the output current.

We know

IE=IB+IC$$I_E=I_B+I_C$$

And

IC=αIE+ICBO$$I_C=\alpha I_E+I_{CBO}$$

=α(IB+IC)+ICBO$$=\alpha (I_B+I_C)+I_{CBO}$$

IC(1−α)=αIB+ICBO$$I_C(1-\alpha )=\alpha I_B+I_{CBO}$$

IC=α1−αIB+11−αICBO$$I_C=\frac{\alpha }{1-\alpha }{I}_B+\frac{1}{1-\alpha }{I}_{CBO}$$

If base circuit is open, i.e. if I_B = 0,

The collector emitter current with base open is I_CEO

ICEO=11−αICBO$$I_{CEO}=\frac{1}{1-\alpha }{I}_{CBO}$$

Substituting the value of this in the previous equation, we get

IC=α1−αIB+ICEO$$I_C=\frac{\alpha }{1-\alpha }{I}_B+I_{CEO}$$

IC=βIB+ICEO$$I_C=\beta I_B+I_{CEO}$$

Hence the equation for collector current is obtained.

Knee Voltage

In CE configuration, by keeping the base current I_B constant, if V_CE is varied, I_Cincreases nearly to 1v of V_CE and stays constant thereafter. This value of V_CEup to which collector current I_C changes with V_CE is called the Knee Voltage. The transistors while operating in CE configuration, they are operated above this knee voltage.

Characteristics of CE Configuration

• This configuration provides good current gain and voltage gain.
• Keeping V_CE constant, with a small increase in V_BE the base current I_Bincreases rapidly than in CB configurations.
• For any value of V_CE above knee voltage, I_C is approximately equal to βI_B.
• The input resistance r_i is the ratio of change in base emitter voltage (ΔVBE$\mathrm{\Delta }{V}_{BE}$) to the change in base current (ΔIB$\mathrm{\Delta }{I}_B$) at constant collector emitter voltage V_CE.
  ri=ΔVBEΔIBatconstantVCE$$r_i=\frac{\mathrm{\Delta }{V}_{BE}}{\mathrm{\Delta }{I}_B}atconstant{V}_{CE}$$
• As the input resistance is of very low value, a small value of V_BE is enough to produce a large current flow of base current I_B.
• The output resistance r_o is the ratio of change in collector emitter voltage (ΔVCE$\mathrm{\Delta }{V}_{CE}$) to the change in collector current (ΔIC$\mathrm{\Delta }{I}_C$) at constant I_B.
  ro=ΔVCEΔICatconstantIB$$r_o=\frac{\mathrm{\Delta }{V}_{CE}}{\mathrm{\Delta }{I}_C}atconstant{I}_B$$
• As the output resistance of CE circuit is less than that of CB circuit.
• This configuration is usually used for bias stabilization methods and audio frequency applications.

Common Collector (CC) Configuration

The name itself implies that the Collector terminal is taken as common terminal for both input and output of the transistor. The common collector connection for both NPN and PNP transistors is as shown in the following figure.

Just as in CB and CE configurations, the emitter junction is forward biased and the collector junction is reverse biased. The flow of electrons is controlled in the same manner. The input current is the base current I_B and the output current is the emitter current I_E here.

Current Amplification Factor (γ)

The ratio of change in emitter current (ΔIE$\mathrm{\Delta }{I}_E$) to the change in base current (ΔIB$\mathrm{\Delta }{I}_B$) is known as Current Amplification factor in common collector (CC) configuration. It is denoted by γ.

γ=ΔIEΔIB$$\gamma =\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_B}$$

• The current gain in CC configuration is same as in CE configuration.
• The voltage gain in CC configuration is always less than 1.

Relation between γ and α

Let us try to draw some relation between γ and α

γ=ΔIEΔIB$$\gamma =\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_B}$$

α=ΔICΔIE$$\alpha =\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}$$

IE=IB+IC$$I_E=I_B+I_C$$

ΔIE=ΔIB+ΔIC$$\mathrm{\Delta }{I}_E=\mathrm{\Delta }{I}_B+\mathrm{\Delta }{I}_C$$

ΔIB=ΔIE−ΔIC$$\mathrm{\Delta }{I}_B=\mathrm{\Delta }{I}_E-\mathrm{\Delta }{I}_C$$

Substituting the value of I_B, we get

γ=ΔIEΔIE−ΔIC$$\gamma =\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_E-\mathrm{\Delta }{I}_C}$$

Dividing by ΔIE$\mathrm{\Delta }{I}_E$

γ=ΔIEΔIEΔIEΔIE−ΔICΔIE$$\gamma =\frac{\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_E}}{\frac{\mathrm{\Delta }{I}_E}{\mathrm{\Delta }{I}_E}-\frac{\mathrm{\Delta }{I}_C}{\mathrm{\Delta }{I}_E}}$$

11−α$$\frac{1}{1-\alpha }$$

γ=11−α$$\gamma =\frac{1}{1-\alpha }$$

Expression for collector current

We know

IC=αIE+ICBO$$I_C=\alpha I_E+I_{CBO}$$

IE=IB+IC=IB+(αIE+ICBO)$$I_E=I_B+I_C=I_B+(\alpha I_E+I_{CBO})$$

IE(1−α)=IB+ICBO$$I_E(1-\alpha )=I_B+I_{CBO}$$

IE=IB1−α+ICBO1−α$$I_E=\frac{I_B}{1-\alpha }+\frac{I_{CBO}}{1-\alpha }$$

IC≅IE=(β+1)IB+(β+1)ICBO$$I_C\cong I_E=(\beta +1)I_B+(\beta +1)I_{CBO}$$

The above is the expression for collector current.

Characteristics of CC Configuration

• This configuration provides current gain but no voltage gain.
• In CC configuration, the input resistance is high and the output resistance is low.
• The voltage gain provided by this circuit is less than 1.
• The sum of collector current and base current equals emitter current.
• The input and output signals are in phase.
• This configuration works as non-inverting amplifier output.
• This circuit is mostly used for impedance matching. That means, to drive a low impedance load from a high impedance source.

Transistor Regions of Operation

The DC supply is provided for the operation of a transistor. This DC supply is given to the two PN junctions of a transistor which influences the actions of majority carriers in these emitter and collector junctions.

The junctions are forward biased and reverse biased based on our requirement. Forward biased is the condition where a positive voltage is applied to the p-type and negative voltage is applied to the n-type material. Reverse biased is the condition where a positive voltage is applied to the n-type and negative voltage is applied to the p-type material.

Transistor biasing

The supply of suitable external dc voltage is called as biasing. Either forward or reverse biasing is done to the emitter and collector junctions of the transistor. These biasing methods make the transistor circuit to work in four kinds of regions such as Active region, Saturation region, Cutoff region and Inverse active region (seldom used). This is understood by having a look at the following table.

EMITTER JUNCTION	COLLECTOR JUNCTION	REGION OF OPERATION
Forward biased	Forward biased	Saturation region
Forward biased	Reverse biased	Active region
Reverse biased	Forward biased	Inverse active region
Reverse biased	Reverse biased	Cutoff region

Among these regions, Inverse active region, which is just the inverse of active region, is not suitable for any applications and hence not used.

Active region

This is the region in which transistors have many applications. This is also called as linear region. A transistor while in this region, acts better as an Amplifier.

This region lies between saturation and cutoff. The transistor operates in active region when the emitter junction is forward biased and collector junction is reverse biased. In the active state, collector current is β times the base current, i.e.,

IC=βIB$$I_C=\beta I_B$$

Where,

IC$I_C$ = collector current

β$\beta$ = current amplification factor

IB$I_B$ = base current

Saturation region

This is the region in which transistor tends to behave as a closed switch. The transistor has the effect of its collector and Emitter being shorted. The collector and Emitter currents are maximum in this mode of operation.

The figure below shows a transistor working in saturation region.

The transistor operates in saturation region when both the emitter and collector junctions are forward biased. As it is understood that, in the saturation region the transistor tends to behave as a closed switch, we can say that,

IC=IE$$I_C=I_E$$

Where IC$I_C$ = collector current and IE$I_E$ = emitter current.

Cutoff region

This is the region in which transistor tends to behave as an open switch. The transistor has the effect of its collector and base being opened. The collector, emitter and base currents are all zero in this mode of operation.

The following figure shows a transistor working in cutoff region.

The transistor operates in cutoff region when both the emitter and collector junctions are reverse biased. As in cutoff region, the collector current, emitter current and base currents are nil, we can write as

IC=IE=IB=0$$I_C=I_E=I_B=0$$

Where IC$I_C$ = collector current, IE$I_E$ = emitter current, and IB$I_B$ = base current.

Transistor Load Line Analysis

Till now we have discussed different regions of operation for a transistor. But among all these regions, we have found that the transistor operates well in active region and hence it is also called as linear region. The outputs of the transistor are the collector current and collector voltages.

Output Characteristics

When the output characteristics of a transistor are considered, the curve looks as below for different input values.

In the above figure, the output characteristics are drawn between collector current I_C and collector voltage V_CE for different values of base current I_B. These are considered here for different input values to obtain different output curves.

Operating point

When a value for the maximum possible collector current is considered, that point will be present on the Y-axis, which is nothing but the saturation point. As well, when a value for the maximum possible collector emitter voltage is considered, that point will be present on the X-axis, which is the cutoff point.

When a line is drawn joining these two points, such a line can be called as Load line. This is called so as it symbolizes the output at the load. This line, when drawn over the output characteristic curve, makes contact at a point called as Operating point.

This operating point is also called as quiescent point or simply Q-point. There can be many such intersecting points, but the Q-point is selected in such a way that irrespective of AC signal swing, the transistor remains in active region. This can be better understood through the figure below.

The load line has to be drawn in order to obtain the Q-point. A transistor acts as a good amplifier when it is in active region and when it is made to operate at Q-point, faithful amplification is achieved.

Faithful amplification is the process of obtaining complete portions of input signal by increasing the signal strength. This is done when AC signal is applied at its input. This is discussed in AMPLIFIERS tutorial.